Search:

Type: Posts; User: gfr-300SRT8

Page 1 of 12 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    20
    Views
    5,937

    If it were me, I'd get my WG and spring to the...

    If it were me, I'd get my WG and spring to the point where I could control the boost down to the 3-5psi range. I was never really happy on the street until I did that, then it was fun to drive again....
  2. Replies
    25
    Views
    14,752

    ^^^ I think your 70/30's and v6 springs will...

    ^^^
    I think your 70/30's and v6 springs will prob work good. The 90/10's didn't work too well for me, front end came up too quick and unloaded the rear when they topped out. Best 60' was low 1.5's....
  3. Replies
    25
    Views
    14,752

    budoboy has the santuffs. I'm going to try these...

    budoboy has the santuffs. I'm going to try these a2speeds(viking shocks) and if i don't get the result i'm looking for I may switch at least the rear to santuffs. They are pricey, but I want to get...
  4. Replies
    25
    Views
    14,752

    A2Speed 05-16 LX / LC Front 3-way Adjustable Coil...

    A2Speed 05-16 LX / LC Front 3-way Adjustable Coil Over Kit

    A2Speed Rear 3-way Adjustable Coil Over Kit - A2Speed.com

    that's what i went with, but I have not had them to the track yet to give...
  5. Replies
    25
    Views
    14,752

    What dbldwn said, suspension first. Guys have...

    What dbldwn said, suspension first. Guys have gone 1.3x on 17's.
  6. Replies
    5
    Views
    771

    FOR SALE Thanks TruckZ, yeah the pics do suck pretty bad....

    Thanks TruckZ, yeah the pics do suck pretty bad. If you bought everything I have there new, it's a little over $1000, just for your info. I can probably dig up some pics of it in the car if that...
  7. Replies
    5
    Views
    771

    FOR SALE Yes

    Yes
  8. I got my boost down to 3.5psi on 38mm WGs with...

    I got my boost down to 3.5psi on 38mm WGs with good primary placement. Do you have pics of your WG placement?
  9. Replies
    10
    Views
    5,321

    With that CR and boost, I can't see you needing...

    With that CR and boost, I can't see you needing to go below .035" with the factory coils, but you can always go lower to rule that out if you want.
  10. Just looked it up, in CMR it is: Delta Throttle...

    Just looked it up, in CMR it is:
    Delta Throttle to Trigger WOT PE
    set this to 2.3V and leave the rest alone
    there is a bunch of torque mgmt stuff that needs to be changed in a boosted application....
  11. also, the limp mode is likely coming from torque...

    also, the limp mode is likely coming from torque mgmt settings. I'd have to get into the sw and refresh my memory on that.
  12. You do NOT want to be in boost in PT, you want to...

    You do NOT want to be in boost in PT, you want to be in WOT in boost as much as possible. The problem is that Chyrs doesn't have a trigger to get you into WOT based on MAP. It's all throttle settings...
  13. Make sure baro updates is off, make sure max baro...

    Make sure baro updates is off, make sure max baro voltage is high enough, make sure max air flow is high enough, make sure max PR is high enough, do NOT change voltage to enable WOT only change...
  14. Replies
    6
    Views
    775

    FOR SALE ​sold

    ​sold
  15. Thread: 6.1 Hemi

    by gfr-300SRT8
    Replies
    6
    Views
    1,272

    WTB I have a 101k miles 6.1 for sale. It has...

    I have a 101k miles 6.1 for sale. It has accessories and brackets, ran perfect when pulled. PM me if you are interested.
  16. sounds more like a drive shaft. you need to get...

    sounds more like a drive shaft. you need to get the car up and do a visual/physical inspection of the drive shaft, carrier bearing, rear transmission mount and diff mounts.
  17. Replies
    129
    Views
    20,948

    Ran E85 for years and a 10.33 on a factory...

    Ran E85 for years and a 10.33 on a factory original with pump E85 without issue. Assuming that gauge is accurate, that will make it easy to monitor. I just used to look at my fuel trims and never had...
  18. Replies
    873
    Views
    152,333

    Personal preference probably. I have a 170 and...

    Personal preference probably. I have a 170 and set my low at 175 and high at 180.
  19. Replies
    4
    Views
    2,394

    If it were me, I would T the reference port off...

    If it were me, I would T the reference port off of the turbo and run that to the solenoid instead of off the intake. The pressure will be greatest off of the turbo. You will have pressure drop across...
  20. Replies
    6
    Views
    775

    FOR SALE I've had it for several years, however I didn't...

    I've had it for several years, however I didn't have it installed in the car the entire time. I only used when flashing a new tune or at the track. Yes it's in perfect working condition.
  21. Replies
    6
    Views
    775

    FOR SALE Yes, unmarried.

    Yes, unmarried.
  22. Replies
    1
    Views
    331

    FOR SALE https://i.imgur.com/IxH6d83.jpg?1 ...

    https://i.imgur.com/IxH6d83.jpg?1

    https://i.imgur.com/7KCf82M.jpg?2
  23. Replies
    1
    Views
    331

    FOR SALE AMS 1000 boost controller for sale

    Description: AMS 1000 boost controller, solenoids and sensor.

    Price (USD): $495

    Location: Wichita Ks
    Shipping & Pickup: Can Meet / Pick Up in person, Can ship within Country
    Shipping Cost...
  24. Replies
    5
    Views
    771

    FOR SALE https://i.imgur.com/8GZSJAe.jpg?1 ...

    https://i.imgur.com/8GZSJAe.jpg?1

    https://i.imgur.com/oF2uWeb.jpg?1
  25. Replies
    5
    Views
    771

    FOR SALE PLX guages for sale

    Description: This is a PLX obd2 gauge. It includes stand alone sensor modules and sensors:
    AFR, 2 EGT, PSI, temp.
    The gauge allows you to show up to 4 sensors at a time. I have had some...
Results 1 to 25 of 300
Page 1 of 12 1 2 3 4